Uniform Sew-Along: Pattern Adjustments

Today in the Uniform Tunic Sew-Along we’re going to discuss a few common pattern adjustments. We’ll start with blending between sizes, cover lengthening or shortening your pattern, and then talk about full and small bust adjustments. This is also our recommended order for adjustments if you need to do more than one. With that, let’s dive in!

Uniform Tunic Pattern Adjustments | Grainline StudioUniform Tunic Pattern Adjustments | Grainline Studio

Blending Between Sizes

Uniform Tunic Pattern Adjustments | Grainline Studio

For this example we’re going to continue with the measurements from our previous Selecting Your Size post so that you can see what those measurements look like in action. As mentioned previously I’ll be disregarding my waist measurement so I’m blending from a 6 at the bust to an 8 at the hips. You’ll want to blend between the bust and hip (around the waist area) rather than from the bust to the hip because you don’t want to affect the measurements at those points, just the area between them. For the separate front and back bodices and skirts the easiest way to smoothly blend, since they’re two pieces that need to sew together as one, is to lay one on top of the other at the seam line. Blend along the side seam and then split the pattern back apart.

You’ll want to make the same blending adjustment to any pattern pieces that cross the point at which you blended or align to the blended pieces. This means if you blend across the waist here you’ll also need to make the same adjustment to the back bodice and back skirt. For pieces that only attach to the garment above or below the blending point you’ll use the size they’re attaching to. So for this example I’d cut a size 6 neck facing and sleeves.

Lengthening and Shortening

Lengthening and shortening your pattern pieces is pretty straightforward, find the lengthen / shorten lines and apply your length changes between them. In the case of the Uniform we’ve only included a lengthen / shorten line on the torso of the pattern. If you need to adjust the lower portion we recommend simply adding onto the hem.

Uniform Tunic Pattern Adjustments | Grainline Studio
  1. Start by locating the pattern pieces you need to adjust.
  2. Cut between the lengthen / shorten lines marked on the pattern. With a piece of paper underneath the pattern, spread the two sections the amount you need to lengthen your piece, making sure to keep the grain line of the two pieces aligned.
  3. Trace your piece off onto the paper and re-blend any gagged edges along the side seam. Repeat the adjustment to any other affected pieces, in the case of the Uniform Tunic, that would be the back.

If you’re shortening the same steps apply only rather than spreading the pieces apart, you’ll be overlapping them the amount you need to shorten the pattern.

Small and Full Bust Adjustment

Now lets talk Full Bust Adjustments. The Uniform Tunic is drafted for a B cup (like all our patterns) so if you’re a C you may be able to get away without a FBA. If you’d like to do a small bust adjustment you would do the opposite of what I’m showing here.

The first thing you need to do before you start your full bust adjustment is to figure out how much of an adjustment you’ll need. To begin you’ll need your upper bust measurement and your full bust measurement. Once you have those you’ll subtract your upper bust from your full bust. If the number you get when you subtract your upper bust from your full bust (the total adjustment) is over 2″ (B cup) you may need a full bust adjustment, whereas if the number you get is 2″ or under you’re either fine to use the pattern as is or you might consider a small bust adjustment. So if your full bust was 40″ and your upper bust was 36″ you’d subtract 40-36 to get 4″ which would require an adjustment.

Now you can take this new number and do one of two things with it. It seems to be the most common to just divide this number in half and apply that amount to each side of the adjustment shown below, so you would be moving the pattern 2″ in Step 3.

Your other option is to take your new number, in our case 4″, and subtract 2″ from it to get the full amount of your bust adjustment. Subtracting the 2″ comes from the fact that the pattern is drafted for a B cup which is a 2″ difference. Since this amount is already drafted into the pattern you are just adding the additional amount on top of what exists. You would then divide the full amount of the adjustment in half so you would be doing a 1″ adjustment on each side of the pattern.

Uniform Tunic Pattern Adjustments | Grainline Studio

To start I prefer to tape the upper and lower pattern pieces together along the stitching line so that you’re performing the adjustments on one piece rather than two. You can definitely adjust the top and then spread the bottom piece to match the added width though, it’s just what you find works for you.

Draw a vertical line from the apex down to the hemline of the pattern making sure to keep the line parallel to the CF / grain line. From there draw a line connecting the apex to the approximate center of the armscye. These are the lines that, along with the dart, will form the full bust adjustment.

Slash through the hemline to the bust and up to the armscye taking care to cut to, but not through, the pattern at that point. You want to make sure that the two pieces are hinged together. Then slice through the line connecting the side seam to the apex, taking care to not cut through the apex point, you want the pieces hinged. You’ll then open the vertical slit the amount of your full bust adjustment making sure that the two edges of the opening are parallel.

Uniform Tunic Pattern Adjustments | Grainline Studio

You’ll notice that when you move the side out for the adjustment the side panel becomes longer than the center front panel. Draw a line extending the pocket marking out to the front edge of the tunic. Cut along this line and align the newly freed piece so that it’s even with both the center front and the pocket marking on the side piece.

Uniform Tunic Pattern Adjustments | Grainline Studio

This method of adjustment results in a widening of the dart. Fold the dart legs together with the takeup pointing towards the bottom of the garment and re-blend the side seam. I like to score the bottom dart leg and center line lightly with an awl to help the pattern fold right where you want it to on the first try. You can either cut across the side seam / dart or mark it with a pattern tracing wheel and cut when the dart is open. You can now open the dart, cut, and separate your top & bottom pieces.

Uniform Tunic Pattern Adjustments | Grainline Studio

One last thing you’ll want to do is to re-align the pocket notches. At the moment your pocket is wider than originally drafted. If your adjustment was small you can probably get away with just connecting the two sides and rolling with it. Keep in mind if you go this route you’ll also need to adjust the width of the pocket lining pattern piece. If you have a larger dart resulting in more pocket spread you may want to consider adjusting the new width to more closely match the original pocket width.

To adjust the upper pattern piece, simply measure over the length of the pocket from the outer notch and remark the inner notch. I typically do this from the outer edge since having pockets too close to the center may look odd proportionally and feel odd functionally as well.

For the lower pattern piece all you need to do is simply move the centermost pocket notch over so that the distance between the two notches matches the distance of the top notches and the pocket. That’s it!

That’s it for adjustments for now. Next up we’ll be talking about cutting and fusing, then it’s time to start sewing!

Related Posts

15 replies on “Uniform Sew-Along: Pattern Adjustments

  • Kelly

    Thanks for the tips! If I’m doing and FBA AND moving the bust dart up and inch, should I do them as two separate steps? I tried to combine them (just shifted the bust apex over and up in one go) but it didn’t go smoothly – my dart was in the right spot but it ended up smaller for some reason.

    Reply
    • Jen

      Yeah, I would recommend them as separate steps. I feel like once things start getting combined it’s impossible to tell where something went wrong.

      Reply
  • Jen

    When deciding which size to cut out for a FBA, do you go by the upper bust measurement or full bust measurement before making the adjustment?

    Reply
  • Helena Wagstaff

    Hi, I have made the willow tank a couple of times and the fit is great straight out of the packet, is this tunic very similar i.e. Bust darts, ease etc. Thanks

    Reply
    • Jen

      They’re a bit different so it’s definitely not a direct transfer of darts, ease, etc. If you have both patterns I’d recommend laying a copy of the Willow pattern you use on top of the Uniform bodice to compare the two together. That should give you a good idea of what you might need to change before you dive into the Uniform.

      Reply
  • Learningwithdonna

    Your technical drawings and help with alterations are stellar. I always check your site whenever I have an adjustment to make. (Or, when I’m just procrastinating and decide to learn something.) Thank you.

    Reply
    • Jen

      Oh that’s so good to hear, thank you! We put a lot of work into it all so I really appreciate you taking the time to let me know you find them useful <3

      Reply
  • Mnberg

    I am a B cup but need to move the Bust point down 1”. If I simply move the whole dart down, the place where the dart now hits the side seam seems very low. Should I lower and rotate the dart up a bit?

    Reply
    • Jen

      So in this case I would probably either just move the bust point and reconnect it to the existing legs, or move the bust point the full inch and the dart legs down as much as you think looks good with the proportions!

      Reply
  • Nancy

    Thanks for your excellent guidance here. Please forgive me if I missed this, but where is the apex of the dart supposed to land on the actual body?

    Reply

Leave a Reply